Kubota ME8200DTN Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 192

background image

ME8200DTN, WSM

HYDRAULIC SYSTEM

N8-S5

3. CHECKING, DISASSEMBLING AND ASSEMBLING

[1] CHECKING AND ADJUSTING

(1) Hydraulic Pump for Power Steering

Hydraulic Flow Test

A

When using flowmeter other than KUBOTA specified
flowmeter, be sure to use the instructions with the
flowmeter.

A

Do not close the flowmeter loading valve completely,
before testing, because it has no relief valve.

1. Disconnect the delivery pipe which is connected from

hydraulic pump to steering controller.

2. Install the adaptor 53 and 54 to the pump discharge port.

[Adaptor 53 and 54 are included in adaptor set (Code No.
07916-54301).]

3. Connect the other hydraulic test hose to the adaptor 53 and

flowmeter inlet port.

4. Connect the other hydraulic test hose to the flowmeter outlet

and put the end of hose into the transmission oil port

5. Open the flowmeter loading valve completely. (Turn

counterclockwise.)

6. Start the engine and set the engine speed at 2000 to 2200

(rpm).

7. Slowly close the loading valve to generate pressure approx.

9.8 MPa (100

, 1422 psi). Hold in this condition until oil

temperature reaches approx. 50

(122

).

8. Open the loading valve completely.
9. Set the engine speed. (Refer to condition.)
10. Read and note the pump delivery at no pressure.
11. Slowly close the loading valve to increase rated pressure.

(Refer to condition.) As the load is increased, engine speed
drops, therefore, reset the engine speed.

12. Read and note the pump delivery at rated pressure.
13. Open the loading valve completely and stop the engine.
14. If the pump delivery does not reach the allowable limit, check

the pump suction line, oil filter or hydraulic pump.

(1)

Power Steering Pump

(2)

Three Point Hydraulic Pump

0000003557E

KiSC issued 04, 2006 A

«
...
159
160
161
162
163
...
»

Содержание ME8200DTN

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ME8200DTN

Бренд: AVANT Страницы: 24

Бренд: GEAppliances Страницы: 16

TDD PLUS TD60D PLUS

Бренд: New Holland Страницы: 16

Бренд: Uni-ram Страницы: 9

Бренд: Original Tractor Cabs Страницы: 21

T2 Versu Series

Бренд: Valtra Страницы: 36

AG PRO PLUS NANT

Бренд: Grouser Products Страницы: 20

Бренд: Husqvarna Страницы: 18

Бренд: Husqvarna Страницы: 18

Бренд: Husqvarna Страницы: 19

Бренд: Still Страницы: 324

Бренд: Branson Страницы: 7

Бренд: Branson Страницы: 135

Бренд: Branson Страницы: 151

Бренд: Branson Страницы: 167

Бренд: Branson Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды