Kubota ME8200DTN Скачать руководство пользователя страница 37

Страница: 37 / 192

ME8200DTN, WSM

ENGINE

N1-S3

Draining Transmission Fluid

1. Place oil pans underneath the transmission case.
2. Remove the drain plugs (1).
3. Drain the transmission fluid.
4. Reinstall the drain plugs (1).

(When reassembling)

Fill up from filling port after removing the filling plug until
reaching the dipstick.

After running the engine for few minutes, stop it and check the
fluid level again, add the fluid to prescribed level if it is not
correct level.

Use only KUBOTA SUPER UDT fluid. Use of other oils
may damage the transmission or hydraulic system.

Refer to "LUBRICANTS, FUEL AND COOLANT" (See
page NG-2.)

Do not mix different brands fluid together.

Foldable ROPS

1. Disconnect the 2P connector from the front combination lamp

(2).

2. Remove the foldable ROPS (1).
3. Remove the ROPS frame right and left (3).

(When reassembling)

Bonnet and Covers

1. Remove the exhaust pipe (1).
2. Remove the bonnet (2).
3. Disconnect the battery's cable.
4. Disconnect the head light 3P connectors.
5. Remove the front lower cover (4) and side cover (5).
6. Remove the bonnet stay (6).

Transmission fluid

Capacity

33.0 L
34.88 U.S.qts
29.04 lmp.qts

(1)

Drain Plug

0000003403E

Tightening torque

ROPS frame (L and R)

193.1 to 225.6

20.0 to 23.0

144.7 to 166.4 ft-lbs

Foldable ROPS

29.4 to 49.0

3.0 to 5.0

21.7 to 36.7 ft-lbs

(1)

Foldable ROPS

(3)

ROPS Frame

(2)

Front Combination Lamp

0000003404E

(1)

Exhaust Pipe

(4)

Front Lower Cover

(2)

Bonnet

(5)

Side Cover

(3)

Battery

(6)

Bonnet Stay

0000003405E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды