Kubota ME8200DTN Скачать руководство пользователя страница 186

Страница: 186 / 192

ME8200DTN, WSM

ELECTRICAL SYSTEM

N9-S3

4WD / Bi-speed Relay

1. Remove the 4WD / Bi-speed relay (4).
2. Apply battery voltage across 1 and 2 terminals, and check for

continuity across 3 and 5 terminals.

3. If continuity is not established across 3 and 5 terminals, relay

is faulty.

The 4WD / Bi-speed relay (4), PTO relay (3), relay 1 (2) and
key stop relay (1) are interchangeable each other.

Turning Angle Inspection Switch

1. Remove the switch cover (3) from the left side front case

support (4).

2. Disconnect the turning angle inspection switch connector (2)

after turning the main switch off.

3. Perform the following checking 1) and 2).

1) Connector Voltage

1. Turn the main switch ON position.
2. Set the 4WD / Bi-speed switch to Bi-speed position.
3. Measure the voltage with a voltmeter across the wiring

harness connector B terminal and chassis.

4. If the voltage differs from the battery voltage (11 to 14 volts),

check the 4WD / Bi-speed switch or wiring harness.

(1)

Key Stop Relay

(3)

PTO Relay

(2)

Relay 1

(4)

4WD / Bi-speed Relay

0000003559E

(1)

Turning Angle Inspection

(3)

Switch Cover

Switch

(2)

Connector

(4)

Front Case Support

0000003380E

Voltage

Connector B terminal

Chassis

Battery voltage

(1)

Turning Angle Inspection

(3)

1P Connector

Switch

(Wiring Harness Side)

(2)

1P Connector (Switch Side)

0000003381E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды