Kubota ME8200DTN Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 192

background image

ME8200DTN, WSM

TRANSMISSION

N3-S27

Disassembling PTO Gear Case

1. Remove the PTO case cover mounting screws and then

remove the PTO gear case cover (6).

2. Remove the stake of the staking nut (8), and then remove it.
3. Remove the bearing (7) by using the bearing puller.
4. Tap out the PTO shaft to the rear side.
5. Remove the gears (11), (14), thrust collars (9), (17), inner

rings (10), (15), hub (13) and shifter (12).

6. Pull out the PTO drive shaft (1) as a unit.
7. Remove the PTO shift fork parts and PTO shift lever parts.

(When reassembling)

A

Reinstall the reamer screw at correct position to mount the
PTO cover case.

A

Direct the grooves of thrust collars (9), (17) to the inner rings
(10), (15) sides.

A

Replace the PTO shaft staking nut (8) with new one, and stake
it firmly after tightening.

A

Apply molybdenum disulfide (Three Bond 1901 or equivalent)
to the inner rings (10) and (15).

A

Apply grease to the oil seal (19) and O-ring.

Tightening torque

PTO shaft staking nut

225.6 to 264.8

23 to 27

166.4 to 195.3 ft-lbs

PTO gear case cover
mounting screws and
reamer screw

77.5 to 90.2

7.9 to 9.2

57.1 to 66.5 ft-lbs

(1)

PTO Drive Shaft

(11)

Gear

(2)

Ball Bearing

(12)

Shifter

(3)

Gear

(13)

Hub

(4)

Gear

(14)

Gear

(5)

Ball Bearing

(15)

Inner Ring

(6)

PTO Gear Case Cover

(16)

Internal Snap Ring

(7)

Ball Bearing

(17)

Thrust Collar

(8)

Stake Nut

(18)

Ball Bearing

(9)

Thrust Collar

(19)

Oil Seal

(10)

Inner Ring

(20)

PTO Shaft

0000001938E

KiSC issued 04, 2006 A

«
...
89
90
91
92
93
...
»

Содержание ME8200DTN

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ME8200DTN

Бренд: Maytag Страницы: 16

Бренд: FENDT Страницы: 267

Бренд: Curtis Страницы: 10

Бренд: Komatsu Страницы: 6

Бренд: Komatsu Страницы: 6

Бренд: Komatsu Страницы: 6

Бренд: Daedong Страницы: 192

Бренд: New Holland Страницы: 21

Бренд: New Holland Страницы: 51

Бренд: New Holland Страницы: 2

Proxima Plus Series

Бренд: Zetor Страницы: 254

Бренд: Land Pride Страницы: 26

PLOWMAXX PLBH 0736-13

Бренд: METAL PLESS Страницы: 24

Бренд: wsm Страницы: 73

Бренд: wsm Страницы: 385

Бренд: Jenn-Air Страницы: 12

ORSO RAPIDO 3000

Бренд: Maschio Страницы: 126

Бренд: MID WEST PRODUCTS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды