Kubota ME8200DTN Скачать руководство пользователя страница 99

Страница: 99 / 192

ME8200DTN, WSM

TRANSMISSION

N3-S35

More than 35 % red lead contact area on the gear tooth surface.
The center of tooth contact at 1/3 of the entire width from the

small end.

Replace the adjusting collar 1 (3) with thicker one to move the

spiral bevel pinion shaft backward.

And place the left side shims to the right side to move the spiral

bevel gear rightward.

Repeat above until the proper tooth contact and backlash are

achieved.

Replace the adjusting collar 1 (3) with a thinner one to move the

spiral bevel pinion shaft forward.

And place the right side shims to the left side to move the spiral

bevel gear leftward.

Repeat above until the proper tooth contact and backlash are

achieved.

Clearance between Differential Case Bore (Differential Case

Cover Bore) and Differential Side Gear Boss

1. Measure the bore I.D. of the differential case and differential

case cover.

2. Measure the differential side gear boss O.D. and calculate the

clearance.

3. If the clearance exceeds the allowable limit, replace them.

(A)

Proper Contact

0000001952E

(B)

Shallow Contact

(C)

Heel Contact

0000003620E

(D)

Deep Contact

(E)

Toe Contact

0000003621E

Clearance between
differential case bore
and differential side
gear boss

Factory spec.

0.050 to 0.151 mm
0.00197 to 0.00594 in.

Allowable limit

0.35 mm
0.014 in.

Differential case bore
I.D.

Factory spec.

40.500 to 40.550 mm
1.59449 to 1.59646 in.

Differential side gear
boss O.D.

Factory spec.

40.388 to 40.450 mm
1.59008 to 1.59252 in.

Clearance between
differential case cover
bore and differential
side gear boss

Factory spec.

0.050 to 0.151 mm
0.00197 to 0.00594 in.

Allowable limit

0.35 mm
0.014 in.

Differential case cover
bore I.D.

Factory spec.

40.500 to 40.550 mm
1.59449 to 1.59646 in.

Differential side gear
boss O.D.

Factory spec.

40.388 to 40.450 mm
1.59008 to 1.59252 in.

0000003497E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды