Kubota ME8200DTN Скачать руководство пользователя страница 142

Страница: 142 / 192

ME8200DTN, WSM

FRONT AXLE

N6-S15

Backlash between 9T Bevel Gear and 43T Bevel Gear

1. Stick a strip of fuse to three spots on the 43T bevel gear (1)

with grease.

2. Fix the axle flange and front gear case.
3. Turn the axle.
4. Remove the axle flange from front gear case and measure the

thickness of the fuse with an outside micrometer.

5. If the backlash is not within the factory specifications, adjust

with shim (3).

(Reference)

Thickness of adjusting shims (3)
1.0 mm (0.039 in.) 1.8 mm (0.071 in.)
1.2 mm (0.047 in.) 2.0 mm (0.079 in.)
1.6 mm (0.063 in.)

Tooth contact : More than 35 %

Backlash between 9T
bevel gear and 43T
bevel gear

Factory spec.

0.25 to 0.35 mm
0.0098 to 0.0138 in.

Allowable limit

0.60 mm
0.024 in.

(1)

43T Bevel Gear

(3)

Shim

(2)

9T Bevel Gear

0000003538E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды