Kubota ME8200DTN Скачать руководство пользователя страница 165

Страница: 165 / 192

ME8200DTN, WSM

HYDRAULIC SYSTEM

N8-S9

Adjusting the Position Rod and Draft Rod

1. Be sure to adjust the position rod length and draft rod length.

Adjusting Uppermost Position

1. Attach the weight (1) of 490 N (50 kgf, 110 lbs) to the end of

lower link (2).

2. Set the position control lever (3) and draft control lever (4) to

the lowest position.

3. Start the engine, and set the engine speed at the 1000 rpm.
4. Set the position control lever (3) to the uppermost position.
5. Shorten the feedback rod by turning the turnbuckle (5) until the

relief valve begins to be operated.

6. From the feedback rod position obtained above 5, turn the

turnbuckle by 1.5 turn to lengthen the feedback rod, then
tighten the lock nut.

7. Move the position control lever down then all the way up. Stop

the engine and check that the lift arm has 5 to 20 mm (0.20 to
0.79 in.) play upward on its edge.

8. If the specified play is not obtained, repeat from 4 again.

Position rod length (A)

Factory spec.

206 mm
8.11 in.

Draft rod length (B)

Factory spec.

172 mm
6.77 in.

0000003562E

Position control
feedback rod A

Factory spec.

Approx. 125 mm
4.92 in.

(1)

Weight

(4)

Draft Control Lever

(2)

Lower Link

(5)

Turnbuckle

(3)

Position Control Lever

0000003563E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды