Kubota ME8200DTN Скачать руководство пользователя страница 89

Страница: 89 / 192

ME8200DTN, WSM

TRANSMISSION

N3-S25

(2) Servicing

4WD / Bi-speed Turn Clutch Disc Wear

1. Measure the thickness of clutch disc with vernier calipers.
2. If the thickness is less than the allowable limit, replace it.

4WD / Bi-speed Turn Drive Plate Wear

1. Measure the thickness of drive plate with vernier calipers.
2. If the thickness is less than the allowable limit, replace it.

Flatness of 4WD / Bi-speed Turn Piston and 4WD / Bi-speed Turn

Drive Plate

1. Place the part on a surface plate.
2. Check it unable to insert a feeler gauge (allowable limit size)

underneath it at least four points.

3. If the feeler gauge can be inserted, replace it.

Thickness of clutch disc

Factory spec.

1.70 to 1.90 mm
0.067 to 0.075 in.

Allowable limit

1.55 mm
0.061 in.

0000003484E

Thickness of drive plate

Factory spec.

1.15 to 1.25 mm
0.045 to 0.049 in.

Allowable limit

1.10 mm
0.043 in.

0000003485E

Flatness of 4WD / Bi-
speed turn piston

Allowable limit

0.15 mm
0.006 in.

Flatness of 4WD / Bi-
speed turn drive plate

Allowable limit

0.30 mm
0.012 in.

0000003486E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды