Kubota ME8200DTN Скачать руководство пользователя страница 100

Страница: 100 / 192

ME8200DTN, WSM

TRANSMISSION

N3-S36

Clearance between Differential Pinion Shaft and Differential

Pinion

1. Measure the differential pinion shaft O.D.
2. Measure the differential pinion I.D. and calculate the

clearance.

3. If the clearance exceed the allowable limit, replace them.

Backlash between Differential Pinion and Differential Side Gear

1. Set a dial indicator (lever type) on the tooth of the differential

pinion.

2. Hold the differential side gear and move the differential pinion

to measure the backlash.

3. If the measurement is not within the factory specifications,

adjust with the differential side gear washer.

(Reference)

Thickness of differential side gear washer :
1.5 mm (0.059 in.)         1.7 mm (0.067 in.)
1.6 mm (0.063 in.)         1.8 mm (0.079 in.)
                                       2.0 mm (0.079 in.)

Clearance between
differential pinion shaft
and differential pinion

Factory spec.

0.060 to 0.102 mm
0.00236 to 0.00402 in.

Allowable limit

0.25 mm
0.010 in.

Differential pinion shaft
O.D.

Factory spec.

19.959 to 19.980 mm
0.78579 to 0.78661 in.

Differential pinion I.D.

Factory spec.

20.040 to 20.061 mm
0.78898 to 0.78980 in.

0000003498E

Backlash between
differential pinion and
differential side gear

Factory spec.

0.15 to 0.30 mm
0.0059 to 0.0118 in.

Allowable limit

0.4 mm
0.016 in.

0000003499E

KiSC issued 04, 2006 A

Содержание ME8200DTN

































































































































































































Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды

Kubota ME8200DTN, Дополнение к руководству по ремонту

Результаты поиска

Содержание ME8200DTN

Отзывы:

Похожие инструкции для ME8200DTN

Бренды по названию

Популярные бренды