Komatsu A31001 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 376

background image

Turn the seat heater switch ON.
(a): OFF position
(b): ON position
The seat cushion and backrest become warm.

METHOD FOR REMOVING AND INSTALLING HEADREST
METHOD FOR REMOVING HEADREST

When the headrest is not necessary, remove it according to the following procedure.
Pull up the headrest 80 mm {3.1 in} or more.
The headrest is pulled out.

NOTICE
When removing the headrest, operate it so that the shaft of
the headrest becomes straight. If it is forcibly twisted, the
installation part may be broken.

METHOD FOR INSTALLING HEADREST

1.

Insert the headrest into the hole at the seat back.
When installing, turn the notch of the shaft toward the front
of the machine.

2.

Push down the headrest.

NOTICE
When installing the headrest, operate it so that the
shaft of the headrest becomes straight. If it is forcibly
twisted, the installation part may be broken.

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-45

«
...
61
62
63
64
65
...
»

Содержание A31001

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A31001

Бренд: Doosan Страницы: 207

Бренд: Doosan Страницы: 211

Бренд: SANY Страницы: 224

Бренд: jcb Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды