Komatsu A31001 Скачать руководство пользователя страница 340 | Manualshive

Страница: 340 / 376

background image

DAILY CALIBRATION

WALK-AROUND CHECKS OF INTELLIGENT MACHINE CONTROL EQUIP-
MENT

Check once a day before starting the engine that the bolts and nuts of the intelligent Machine Control are not
loose, the wiring harness connector is not loose, and the play is proper.

METHOD FOR CHECKING GNSS ANTENNA AND CABLE

1.

Check that the installing direction of GNSS antenna
matches marks.
If it is misaligned, loosen the mounting knob (1) and align it
so that marks are in a straight line.

2.

When the connector (2) of GNSS antenna is connected,
tighten the thread while pushing it in the direction of arrow.
If it is tightened lightly, it may become loose during opera-
tion.

METHOD FOR CHECKING GNSS RADIO DEVICE

When GNSS radio device is installed, check that antenna is not faulty, installed position is not behind the ma-
chine, antenna cable coating is not damaged, and connector is not loosened.

METHOD FOR CHECKING LOOSENESS OF CONTROL BOX

1.

Check that the control box is located in the position for you to see it well, and the visibility of front right of
cab is good. If visibility is not good, adjust the angle of control box.

2.

Check that control box is fixed securely. If mounting knob is loose, retighten it further.

METHOD FOR CHECKS BEFORE STARTING ON intelligent Machine Control
EQUIPMENT

Before starting the work each day, perform the following inspection to check that the intelligent Machine Control
is detecting the bucket edge position correctly.
1.

Check that the battery disconnect switch (S) is in ON posi-
tion (I).

DAILY CALIBRATION

EXECUTIONS

8-30

«
...
338
339
340
341
342
...
»

Содержание A31001

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A31001

Бренд: Case Страницы: 306

Бренд: Komatsu Utility Страницы: 254

Бренд: Daewoo Страницы: 16

Бренд: Takeuchi Страницы: 352

Бренд: Komatsu Страницы: 51

Galeo PC800LC-8

Бренд: Komatsu Страницы: 318

Бренд: Yuchai Страницы: 184

Бренд: RHINO Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды