Kobelco SK135SR-7 Скачать руководство пользователя

Страница: 5 / 412

［

CONTENTS

］

2.7.1

FUSIBLE LINK INSPECTION/REPLACEMENT........................................................................... 2-58

CONTROLLER ............................................................................................................................... 2-59

2.9

HANDLING OF RADIO .................................................................................................................... 2-60

2.9.1

NAME OF EACH PART ............................................................................................................. 2-60

2.9.2

ON-AIR (NORMAL CONDITION) ............................................................................................... 2-61

2.9.3

SWITCHING SOURCE .............................................................................................................. 2-62

2.9.4

FM/AM ..................................................................................................................................... 2-63

2.9.5

BLUETOOTH AUDIO FUNCTION, AND USB PORT/EXTERNAL INPUT TERMINAL..................... 2-68

2.9.6

PAIRING (REGISTRATION OF DEVICES).................................................................................. 2-71

2.9.7

TELEPHONE FUNCTION.......................................................................................................... 2-73

2.9.8

FILE PLAYING FUNCTION ........................................................................................................ 2-75

2.9.9

VOLUME CONTROL................................................................................................................. 2-82

2.9.10

SOUND ADJUSTMENT ........................................................................................................... 2-83

2.9.11

CLOCK ADJUSTMENT............................................................................................................ 2-87

2.10

AIR CONDITIONER....................................................................................................................... 2-88

2.10.1

GRILLE (AIR OUTLET)............................................................................................................ 2-88

2.10.2

AIR CONDITIONER CONTROL PANEL.................................................................................... 2-89

2.10.3

AIR CONDITIONER OPERATION PANEL................................................................................. 2-90

2.10.4

HOW TO USE AIR CONDITIONER .......................................................................................... 2-93

2.10.5

SELF-DIAGNOSIS FUNCTION IN DISPLAY MONITOR............................................................. 2-95

2.10.6

HANDLING AT IN-SEASON/OFF-SEASON .............................................................................. 2-96

2.11

HANDLING OF SEAT BELT............................................................................................................ 2-97

2.11.1

HOW TO FASTEN SEAT BELT................................................................................................. 2-97

2.11.2

HOW TO UNFASTEN SEAT BELT ............................................................................................ 2-97

2.12

HANDLING OF OPERATOR'S SEAT (AIR SUSPENSION SEAT)...................................................... 2-98

2.12.1

DAMPER ADJUSTMENT......................................................................................................... 2-98

2.12.2

WEIGHT ADJUSTMENT.......................................................................................................... 2-99

2.12.3

HEIGHT ADJUSTMENT........................................................................................................... 2-99

2.12.4

RECLINING ADJUSTMENT..................................................................................................... 2-99

2.12.5

FRONT/REAR ADJUSTMENT OF CONTROL STAND............................................................... 2-99

2.12.6

TILT ADJUSTMENT OF CONTROL BOX .................................................................................. 2-99

2.12.7

FRONT/REAR ADJUSTMENT OF SEAT ................................................................................ 2-100

2.12.8

TILT ADJUSTMENT OF SEAT SEATING SURFACE ................................................................ 2-100

2.12.9

FRONT/REAR ADJUSTMENT OF SEAT SEATING SURFACE................................................. 2-100

2.12.10

ARM REST ADJUSTMENT .................................................................................................. 2-100

2.12.11

HEAD REST ADJUSTMENT................................................................................................. 2-100

2.12.12

SEAT HEATER.................................................................................................................... 2-100

2.12.13

LUMBAR SUPPORT ........................................................................................................... 2-100

2.13

HANDLING PARTS INSIDE CAB.................................................................................................. 2-101

2.13.1

CAB DOOR LOCK................................................................................................................. 2-101

2.13.2

OPENING DOOR FROM INSIDE OF CAB .............................................................................. 2-101

2.13.3

OPENING/CLOSING FRONT WINDOW (UPPER)................................................................... 2-102

2.13.4

REMOVING FRONT WINDOW (LOWER) ............................................................................... 2-103

2.13.5

ROOM LAMP ........................................................................................................................ 2-104

2.14

EMERGENCY ESCAPE FROM OPERATOR'S STATION ............................................................... 2-105

2.15

OTHER ACCESSORIES.............................................................................................................. 2-106

2.15.1

TOOL BOX ........................................................................................................................... 2-106

Содержание SK135SR-7


































































































































































































































































































































































































Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды

Kobelco SK135SR-7, Руководство по эксплуатации

Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды