Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 360 / 412

background image

7-4

［

MACHINE OPERATION MANAGEMENT SYSTEM

7.2

REMOTE DOWNLOAD SYSTEM

This system sometimes automatically renews (downloads) the software of the controller in this machine.
At that time, the instruction will appear on the monitor, so that operate the jog dial.

a

g

e

c

d

c

b

f

d

Jog dial operation

Tilting (a,b,c,d) and rotating (e,f) the jog dial

To move the cursor on the monitor and adjust the values
and others.

Pushing down (g) the jog dial

• To switch the screen to the selected setting screen.

•

To determine the adjusted value and others.

SOFTWARE IS TO BE UPDATED

AFTER KEY SW OFF, PWR OFF IS
IMPOSSIBLE FOR ABOUT 10 MINUTES
DO YOU ALLOW UPDATE?

CANCEL

ACCEPT

SOFTWARE IS BEING UPDATED
AUTO PWR OFF AFTER UPDATE

CAUTION!
UPDATE STOPS BY KEY SW ON
DO NOT CUT BAT PWR AT UPDATE

1.

If update of the software is possible, when the
starter switch is turned to the "ON" or "START"
position and the engine is started, the following
selection screen appears on the monitor.

2.

Using the jog dial, move the cursor to [ACCEPT].

3.

Push down (g) the jog dial to set preparation of
update. (At this time, the updating of the software
does not start)

4.

Then the screen returns to the normal screen, so
that continue the machine operation.

5.

Then, turn the starter key to the "OFF" position to
display the following screen on the monitor, and
then the update of the software starts. The update
takes almost 10 minutes.

During the renewal of the software, do not turn OFF the battery power-off switch or remove the battery terminals. If
the battery power is shut off during the renewal, it can damage the controller.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
358
359
360
361
362
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Yuchai Страницы: 154

Бренд: Kubota Страницы: 118

Бренд: JackRabbit Страницы: 21

Бренд: VMB Страницы: 14

Бренд: VMB Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды