Kobelco SK135SR-7 Скачать руководство пользователя

Страница: 390 / 412

8-28

［

OPTIONAL EQUIPMENT

］

8.9.2

PROHIBITED WORKS

DO NOT PERFORM LIFTING WORK

Never perform any lifting work using the quick hitch. A
lifted load may fall and cause serious accidents.

DO NOT WORK WITHOUT FRONT ATTACHMENT

Do not lift a load or the machine, when the front
attachment is not installed. It may cause damage to the
quick hitch.

DO NOT LIFT OR MOVE PERSONNEL

Never lift or move personnel by using the quick hitch.
The lifted personnel may fall off, causing severe
accidents.

Содержание SK135SR-7


































































































































































































































































































































































































Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды

Kobelco SK135SR-7, Руководство по эксплуатации

Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды