Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 67 / 412

background image

1-43

SAFETY INSTRUCTIONS

ROTATING PARTS

Stay clear of all rotating and moving parts.

• Wrapping or entanglement may result in serious injury

or death. Keep hands, clothing and tools away from
the rotating fan and running fan belts. Never operate
machine without guarding in place.

• Do not drop or insert tools and others to the fan and

belt. They will be blown away or damaged, resulting in
serious personal injury or death.

• Always have an operator at the controls to shut down

the machine if the machine needs to be running for
maintenance activity or an inspection. The operator and the maintenance personnel must have a means of
communication when performing these tasks.

VENTILATION PRECAUTIONS

Never operate the engine in an enclosed area without
adequate ventilation. Engine exhaust contains carbon
monoxide. Inspecting and maintaining the machine
indoors or in a place with poor ventilation could cause
serious injury or death.
Adequate ventilation is needed when inspecting,
maintaining or running the machine indoors. Fully
ventilate the work area, especially when handling fuel,
cleaning solvent or paint.
If the natural ventilation is poor, install ventilators, fans,
exhaust extension pipes or other artificial venting
devices.

CONNECTING, DISCONNECTING AND STORING ATTACHMENT / EQUIPMENT

To prevent serious injury or death:
• Always follow the instructions from your supervisor

and the instructions in this manual when connecting
or disconnecting the attachment /equipment.

• Secure the attachment /equipment to prevent them

from falling over when stored.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
65
66
67
68
69
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: jcb Страницы: 3

Бренд: SANY Страницы: 276

Бренд: ZHONGTIAN Страницы: 12

Бренд: Yuchai Страницы: 152

Бренд: Cambridge Elevating Страницы: 21

Бренд: Meec tools Страницы: 38

Бренд: Meec tools Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды