Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 46 / 412

background image

1-22

［

SAFETY INSTRUCTIONS

1.3

SECURE VISIBILITY

READ THE OPERATOR'S MANUAL

Read, understand and follow the safety messages and instructions in this manual. If these safety messages are not
followed, serious injury or death could occur.

1.3.1

BE AWARE OF YOUR SURROUNDINGS

When operating or traveling in the machine, the operator may not observe people and obstacles near the machine.
To prevent serious injury, death or damage to the machine.

• Adjust the mirrors for maximum visibility around the machine before operating. If needed, clean the mirrors.

• If the machine is equipped with the rearview camera and the side cameras, clean the lenses to display clear

images from the rearview and side cameras to the monitor.

• There are blind spots in the mirror and camera views. Confirm for safety around the machine before operating

the machine.

• Move the attachment /equipment as needed to improve visibility of the right side during machine travel.

• If needed, use a signal person. The operator should always be alert and follow the signals from the signal

person. The operator shall respond to signals only from the appointed signal person, but shall obey a stop signal
from anyone at any time.

• When operating in dark locations, turn on the work light. Additional lighting may be needed to illuminate the work

area.

• Stop work if you have poor or limited visibility because of darkness, fog, rain, especially lightning, snow, or other

causes.

• Never attach mirrors or other articles to the handrails. Over time, excessive vibration may weaken the handrail

and cause it to fail.

• If a failure occurs on the rearview camera or the side camera, contact your KOBELCO authorized dealer for

repair.

• Do not operate the machine without the monitor pictures of the rearview camera and the side camera being

displayed.

• Do not remove or disassemble the rearview camera and the side camera systems.

The camera systems are installed on the base machine according to ISO 16001:2017. When removal or
disassembly of them is required, contact your KOBELCO authorized dealer otherwise it may void the machine
warranty.

MIRROR AND CAMERA LOCATION

Only use genuine KOBELCO mirrors, rearview camera system, and side camera system.
Regarding adjustment of the mirrors and the rearview camera, see "ADJUSTMENT OF MIRRORS" in Chapter 3.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
44
45
46
47
48
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Komatsu Страницы: 261

Бренд: WCM Страницы: 52

Бренд: SANY Страницы: 196

Бренд: SANY Страницы: 288

Бренд: Agrison Страницы: 83

Бренд: Garbin Страницы: 72

Бренд: jcb Страницы: 31

Бренд: Case Страницы: 22

Бренд: Case Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды