Kobelco SK135SR-7 Скачать руководство пользователя

Страница: 102 / 412

2-28

［

MACHINE FAMILIARIZATION

］

2.3.13

SWITCHING ATTACHMENT MODE

Select an appropriate mode to use according to the attachment installed.

Display

Attachment mode

Summary

Bucket

This mode needs to be selected for digging work.

Breaker

This mode needs to be selected when an attachment using a single
flow circuit such as a breaker is installed.

Nibbler (crusher)

This mode needs to be selected when a hydraulic crusher such as a
nibbler is installed.

Rotary grapple

This mode is designed considering the operation such as a grapple.

Processor

This mode is designed considering the operation such as a
processor.

Thumb bucket

This mode is designed considering the operation such as a thumb
bucket.

Rotary tilt

This mode is designed considering the operation such as a rotary tilt.

Individual setting

This mode can be customized for an attachment other than those
mentioned above.

• When the attachment mode is inappropriate, select a proper attachment mode.

• Always select the breaker mode when operating a breaker. Working in a mode other than the breaker mode

causes damages to the hydraulic components and/or the breaker.

• Be sure to lower the attachment to the ground and ensure safety before switching the attachment mode.

• If tuning of operability is needed, contact your KOBELCO authorized dealer.

• When the control lock lever is raised upward to the "LOCKED" position, setting for changing the screen becomes

possible.

Содержание SK135SR-7


































































































































































































































































































































































































Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды

Kobelco SK135SR-7, Руководство по эксплуатации

Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды