Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 200 / 412

background image

3-18

［

MACHINE OPERATION

］

3.2.11

CHECKING DISPLAY OF MONITOR

Before starting the engine, check the display status of the monitor according to the following procedure.

When the warning is displayed on the monitor, ask your KOBELCO authorized dealer for inspection.

1.

Make sure the pilot control lock lever is in the "LOCKED" position.

2.

Make sure all control levers are in the "NEUTRAL" position.

3.

Turn the key of the starter switch to the "ON" position.

4.

Check that no warning is displayed on the monitor.

3.2.12

CHECKING WORKING LIGHT

While the starter switch is in the "ON" position, press the
working light switch to turn on the working lights on the
boom and on the right side of the front. If they do not
light, presumably light bulbs are burned out or the
electrical wire is broken. Ask your KOBELCO authorized
dealer for repair.

3.2.13

CHECKING OF AIR CLEANER INLET

•

Check that no mud, leaves, and snow, etc. are accumulated around the air cleaner inlet.

•

When it is covered with snow, remove it.

•

When washing the machine with high-pressure water for cleaning, be careful not to let the water enter the air
cleaner inlet.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
198
199
200
201
202
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: U.S. General Страницы: 9

Бренд: SANY Страницы: 196

Бренд: ZHONGTIAN Страницы: 12

Бренд: Barreto Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды