Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 70 / 412

background image

1-46

［

SAFETY INSTRUCTIONS

DO NOT DISASSEMBLE THE RECOIL SPRING

Never attempt to disassemble the recoil spring. The recoil spring assembly acts as a shock absorber for the front
idler and contains a powerful spring under tension. If it is disassembled, the spring will eject from the assembly and
result in severe personal injury or death.
If there is an issue with the recoil spring assembly, contact your KOBELCO authorized dealer for repair.

BEFORE HAMMERING METAL PINS, TEETH OR BEARINGS

Always wear required personal protective equipment such as safety glasses when using hammers, as metal
fragments or other objects can fly and cause serious personal injury.
Broken metal pieces may cause severe personal injury when hammering metal pins, teeth or bearings.
To avoid injury:
• Wear protective gears such as safety glasses, gloves,

hardhat, protective shoes, etc.

• Confirm the work area is clear of personnel before

using hammer.

• Use a piece of wood or similar material to absorb the

direct impact of the hammer when removing metal
pins, teeth or bearings.

BE AWARE OF THE HAZARDS WITH THE REFRIGERANT AND THE AIR CONDITIONING SYSTEM

• Do not loosen the refrigerant circuit parts. If refrigerant gets in your eyes, it may cause loss of sight including

potential blindness. Do not touch the refrigerant circuit parts. If refrigerant gets on your skin, it may cause
frostbite.

• Do not inhale refrigerant gas; and

• Keep refrigerant gas away from heat sources.

Dispose of refrigerant according to local codes and regulations of each country.
If you need additional assistance, contact your KOBELCO authorized dealer about proper disposal of refrigerant.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
68
69
70
71
72
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Komatsu Страницы: 9

Galeo PC1250-7 Backhoe

Бренд: Komatsu Страницы: 9

Бренд: Komatsu Страницы: 61

Бренд: Komatsu Страницы: 61

Бренд: Wacker Neuson Страницы: 188

Бренд: JackRabbit Страницы: 38

Бренд: Yuchai Страницы: 183

Бренд: Takeuchi Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды