Kobelco SK135SR-7 Скачать руководство пользователя страница 317 | Manualshive

Страница: 317 / 412

background image

4-85

INSPECTION AND MAINTENANCE

4

FULL

LOW

15. Install the under cover under the radiator.

16. After the coolant cools down enough, check the

coolant levels at the radiator filler opening and the
reserve tank (4).

• If the coolant level at the radiator filler opening

becomes low, refill the coolant.

• Refill the reserve tank (4) with the coolant up to

the middle between FULL (upper limit) to LOW
(lower limit).

4.19.2

REPLACING OIL IN SWING REDUCTION UNIT

HANDLING OF OIL IMMEDIATELY AFTER OPERATION

Immediately after operation, the oil is hot and it may cause burns. Start working after the temperature goes down.

Replace the oil after 500 hours of operation has been reached for the first time.

• Check drain oil, and if metal chips or powder is found in the oil, contact your KOBELCO authorized dealer.

• Dispose of the drain waste oil properly as industrial waste.

1.

Move the machine to a level and firm place.

2.

Put the bucket on the ground.

3.

Stop the engine and move the pilot control shut-off lever to the "LOCKED" position.

2

1

4.

Place a container for drain oil under drain plug (1) at
the rear lower part of swing reduction unit.
Container: 1.6 L (0.4 Gal) or more

5.

Remove level gauge (2) and refill the specified gear
oil to the specified quantity.
When the oil level is within the specified range of the
scale of level gauge (2), it is proper.
For the specified gear oil, see "LUBRICANT, FUEL
& COOLANT SPECIFICATIONS" in Chapter 4.

6.

Attach level gauge (2).

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
315
316
317
318
319
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Gehl Страницы: 132

Бренд: Mitsubishi Страницы: 14

Бренд: jcb Страницы: 20

PC850-8 BACKHOE

Бренд: Komatsu Страницы: 8

Бренд: Komatsu Страницы: 8

PC750-7 BACKHOE

Бренд: Komatsu Страницы: 41

Бренд: Komatsu Страницы: 41

Бренд: Komatsu Страницы: 51

Бренд: Komatsu Страницы: 203

Бренд: Komatsu Страницы: 412

Бренд: Komatsu Страницы: 442

Бренд: Komatsu Страницы: 446

Бренд: Komatsu Страницы: 462

Бренд: Komatsu Страницы: 758

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды