Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 175 / 412

background image

2-101

［

MACHINE FAMILIARIZATION

2.13

HANDLING PARTS INSIDE CAB

LEAVING OPERATOR'S SEAT

Do not leave the cab with the engine running.
When necessary to leave the operator's seat, be sure to lock the control lock lever and then stop the engine.
If the control lever is unexpectedly touched without the control lock lever locked, it may cause severe accident
resulting in severe injury.

2.13.1

CAB DOOR LOCK

In operation, lock the door securely either open or close. If not locked, the door may open or close unexpectedly
and this may cause danger and failure of the machine.

This procedure is used to securely lock the door in open position.

2

1

•

Push the door against catch (1) and check that it is
locked securely.

•

To close the door, move lever (2) on the left side of
the operator's seat to the direction of the arrow and
then the catch is released.

2.13.2

OPENING DOOR FROM INSIDE OF CAB

1

•

To open the door from the inside of the cab, move
lever (1) to the direction of the arrow.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
173
174
175
176
177
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Case Страницы: 306

Бренд: Wacker Neuson Страницы: 254

Бренд: JACK RABBIT Страницы: 32

Robex 290LC-9MH

Бренд: Hyundai Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды