Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 237 / 412

background image

4-5

INSPECTION AND MAINTENANCE

4.2.3

SUPPORT STAY

The support stays are provided on the side doors and the engine hood.
When opening the side doors and the engine hood, be sure to fix them with the stays

Before performing inspection or maintenance, be sure to fix the opened side doors and the opened engine hood
with the support stays to prevent them from moving, resulting in personal injury.

Stay fixed by hole

1

2

Open the door, and put stay (1) into fixing hole (2) to fix
the stay.
Before closing the door, remove the stay from the fixing
hole, return it to the original position, and then close the
door.

Slide type stay

2

1

2

1

Open the door, slide stay (1) to fixing part (2) of the guide
to fix the stay.
Before closing the door, remove the stay from fixing part
(2) and then close the door.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
235
236
237
238
239
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: OLEO Страницы: 52

Бренд: GSi Страницы: 38

Бренд: Daewoo Страницы: 658

Бренд: Fantek Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды