Kobelco SK135SR-7 Скачать руководство пользователя

Страница: 7 / 412

［

CONTENTS

］

3.11.3

GROUND LEVELING WORK ................................................................................................... 3-42

3.12

ALWAYS PARK MACHINE PROPERLY .......................................................................................... 3-43

3.12.1

PARKING MACHINE ON SLOPE ............................................................................................. 3-43

3.13

INSPECTION AND CHECK AFTER OPERATION............................................................................ 3-45

3.14

MACHINE OPERATION IN ADVERSE CONDITIONS ...................................................................... 3-46

3.14.1

OPERATION IN COLD CONDITION ......................................................................................... 3-46

3.14.2

OPERATION AT SEASHORE................................................................................................... 3-47

3.14.3

OPERATION IN SANDY AND DUSTY AREAS........................................................................... 3-47

3.15

PRECAUTIONS FOR LONG-TERM STORAGE .............................................................................. 3-48

3.15.1

WASHING MACHINE .............................................................................................................. 3-48

3.15.2

REFILLING OIL/GREASING .................................................................................................... 3-48

3.15.3

BATTERY ............................................................................................................................... 3-48

3.15.4

COOLANT .............................................................................................................................. 3-48

3.15.5

PREVENTION OF DUST AND MOISTURE ............................................................................... 3-49

3.15.6

PERIODICAL LUBRICATING OPERATION (DURING STORAGE) ............................................. 3-49

3.15.7

TREATMENT AFTER LONG-TERM STORAGE......................................................................... 3-49

INSPECTION AND MAINTENANCE

4.1

GENERAL ........................................................................................................................................4-3

4.2

INSPECTING AND MAINTAING MACHINE.........................................................................................4-4

4.2.1

PERIODIC INSPECTION AND MAINTENANCE............................................................................4-4

4.2.2

PRECAUTIONS OF INSPECTION AND MAINTENANCE ..............................................................4-4

4.2.3

SUPPORT STAY .........................................................................................................................4-5

4.3

EXHAUST GAS CLEANING DEVICE (DOC) .......................................................................................4-6

4.3.1

ABOUT EXHAUST GAS CLEANING DEVICE ...............................................................................4-6

4.3.2

ABOUT AUTOMATIC REGENERATION .......................................................................................4-6

4.3.3

ABOUT MANUAL REGENERATION.............................................................................................4-7

4.3.4

INSPECTION AND MAINTENANCE.............................................................................................4-8

4.3.5

PRECAUTIONS OF USING EXHAUST GAS CLEANING DEVICE .................................................4-9

4.4

SCR SYSTEM AND DEF/ADBLUE ................................................................................................... 4-10

4.4.1

SCR ......................................................................................................................................... 4-10

4.4.2

DEF/AdBlue.............................................................................................................................. 4-10

4.4.3

DEF/AdBlue CIRCUIT AND BATTERY........................................................................................ 4-10

4.4.4

STORING DEF/ADBLUE ........................................................................................................... 4-10

4.4.5

PURCHASING DEF/ADBLUE .................................................................................................... 4-10

4.4.6

LOW DEF/ADBLUE LEVEL ....................................................................................................... 4-11

4.4.7

QUALITY PROBLEMS OF DEF/ADBLUE ................................................................................... 4-11

4.4.8

DRAINING DEF/ADBLUE .......................................................................................................... 4-12

4.4.9

FAILURE OF EXHAUST GAS CLEANING DEVICE ..................................................................... 4-13

4.4.10

EMERGENCY EVACUATION MODE........................................................................................ 4-14

4.4.11

SCR INSPECTION AND MAINTENANCE ................................................................................. 4-14

4.5

LUBRICANT, FUEL & COOLANT SPECIFICATIONS ......................................................................... 4-15

4.6

ABOUT USE OF BIO-OIL (BIODEGRADABLE HYDRAULIC OIL)....................................................... 4-17

4.6.1

GREASE AND OIL FOR USE .................................................................................................... 4-17

4.6.2

PRECAUTIONS FOR BIO-OIL ................................................................................................... 4-17

4.6.3

REPLACEMENT INTERVAL OF BIO-OIL.................................................................................... 4-17

Содержание SK135SR-7


































































































































































































































































































































































































Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды

Kobelco SK135SR-7, Руководство по эксплуатации

Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды