Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 243 / 412

background image

4-11

INSPECTION AND MAINTENANCE

4.4.6

LOW DEF/ADBLUE LEVEL

If the pointer of the monitor points the yellow or red range, immediately supply DEF/AdBlue until the pointer points
the place higher than the yellow range.
When DEF/AdBlue becomes low, restriction is applied to the engine output.

When the following warnings are displayed in the multi-display, see "CHECKING DEF/ADBLUE LEVEL AND
REFILLING" to supply DEF/AdBlue.

Level

Warning Display

Contents

1st Level

Displayed with the warning sound when the pointer of the DEF/
AdBlue level gauge points the yellow range.

2nd Level

Displayed with the warning sound when the pointer of the DEF/
AdBlue level gauge points the yellow range. Gradually, a restriction is
applied to the engine output.

3rd Level

Displayed with the continuous warning sound when the pointer of the
DEF/AdBlue level gauge points the E point. The engine output is
further restricted than Level 2.

4.4.7

QUALITY PROBLEMS OF DEF/ADBLUE

• Use DEF/AdBlue which meets ISO 22241-1 or JIS K2247-1.

• Do not add diesel fuel or water in the DEF/AdBlue tank.

• Follow the precautions for handling DEF/AdBlue specified by the manufacturer.

When the following warnings are displayed on the multi-display, something other than DEF/AdBlue is in the DEF/
AdBlue tank. See "DRAINING DEF/ADBLUE" and "CHECKING DEF/ADBLUE LEVEL AND REFILLING " to drain
and refill DEF/AdBlue.
If the machine is operated with the DEF/AdBlue in abnormal quality, the engine output is restricted.
Also, when something else than DEF/AdBlue is put in the tank and the engine is started, the DEF/AdBlue pipes and
the DEF/AdBlue supply module may need to be replaced.

LEVEL

Warning Display

Description

Level 1

Displayed with the warning sound when the DEF/AdBlue sensor
determines the quality problem of DEF/AdBlue.

Level 2

Displayed with the warning sound when a certain period of time has
passed from Level 1. The engine output is gradually restricted.

Level 3

Displayed with the continuous warning sound when a certain period
of time has passed from Level 2. The engine output is further
restricted than Level 2.

When failure of the DEF/AdBlue quality or the exhaust gas cleaning device occurs repeatedly, the warning level
goes up. If another failure of the DEF/AdBlue quality or the exhaust gas cleaning device occurs in a short period of
time after the failure of that is corrected, the warning level starts from Level 3.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
241
242
243
244
245
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: jcb Страницы: 332

Бренд: Cambridge Elevating Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды