Kobelco SK135SR-7 Скачать руководство пользователя страница 289 | Manualshive

Страница: 289 / 412

background image

4-57

INSPECTION AND MAINTENANCE

REPLACING RADIATOR HOSES

REPLACING RADIATOR HOSES

Inside the radiator, the high pressure steam occurs and it may cause personal injury. Do not loosen or remove the
radiator cap when the coolant is under high pressure and high temperature.

• Stop the engine before removing the radiator cap.

• Allow enough time for the coolant to cool down before removing the radiator cap.

1

1

2

1

2

1

3

1.

Loosen four bolts under the radiator, and remove
the cover.

2.

Loosen radiator cap (1) slowly. After checking that
the pressure is completely released, push the cap
down, loosen it further, and then remove it.

3.

Loosen drain cock (3) and drain the coolant into a
container until the water level of the radiator
becomes lower than hose (2) to replace.

4.

Loosen clamp (1), remove damaged hose (2), and
replace it with a new hose.

5.

Tighten drain cock (3).

6.

Refill the radiator with coolant and then fill the
reserve tank with coolant.

7.

After refilling, tighten the radiator cap securely.

8.

Remove the support stay, and close the engine
hood.

9.

Install the cover on the specified position under the
radiator.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
287
288
289
290
291
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: SANY Страницы: 166

Бренд: Fantek Страницы: 36

Бренд: Galeo Страницы: 299

Бренд: STC Страницы: 25

Бренд: Fraco Страницы: 69

Бренд: BCS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды