Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 58 / 412

background image

1-34

［

SAFETY INSTRUCTIONS

REMOVING DIRT OF BUCKET

With the bucket in the retracted position, do not give
impact on the bucket to remove soil. It may cause
damage to the equipment/attachment and cylinders.

LIFTING WORK

This machine is designed for the application of digging,
loading, and leveling using the bucket.
Furthermore, some machines are designed in
consideration of works with a breaker, crusher, or others
installed.
When lifting a load by using this machine, observe the
laws and others of the country or area in which this
machine is to be used.
Even though lifting with this machine is allowed
according to the laws of the country or area in which this
machine is to be used, do not lift the load by using the
teeth of the bucket, the breaker, the crusher, or others.
It can cause the lifting tools to come off and result in
falling off of the load, leading to serious accidents or death.

DO NOT OPERATE THE CYLINDERS TO THE STROKE END

A

A

Operate the bucket, boom and arm cylinders to leave
some clearances (A) to the both stroke ends. If the
cylinder is operated to the stroke end, it will generate an
excessive load and cause damage to not only the
cylinder but also the pin, boom and arm.

DO NOT OPERATE IN ENCLOSED SPACES

Do not operate the machine in enclosed spaces or, in any case, without appropriate ventilation.

PRECAUTIONS FOR POTENTIALLY EXPLOSIVE ENVIRONMENT

When using the machine in a potentially explosive environment, comply with local codes and regulations of each
country.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
56
57
58
59
60
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Takeuchi Страницы: 9

Бренд: CASE CONSTRUCTION Страницы: 256

Бренд: Hitachi Страницы: 278

Бренд: OLEO Страницы: 12

Бренд: EIK Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды