Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 142 / 412

background image

2-68

［

MACHINE FAMILIARIZATION

］

2.9.5

BLUETOOTH AUDIO FUNCTION, AND USB PORT/EXTERNAL INPUT
TERMINAL

Using the Bluetooth Audio function, and USB port/external input terminal (AUX) of this machine, you can listen to
music from a cell phone and external sound device.

Bluetooth Audio

• The Bluetooth Audio function of this machine does not guarantee wireless connection with all types of devices

supporting Bluetooth. Devices like cell phones, etc. to be connected need to meet the Bluetooth standard
determined by SIG and to be certified. Even if devices to be connected meet the Bluetooth standard, some
devices may have connection problems, display/operation differences, or skipping sound.

• For the use of Bluetooth, follow the instruction manual of each device.

• Bluetooth in this machine may adversely affect some medical electric devices such as a cardiac pacemaker.

When using Bluetooth Audio near medical electric devices, be very careful and ask applicable medical electric
device manufacturers beforehand for use of Bluetooth.

USB PORT/EXTERNAL INPUT TERMIANL (AUX)

• USB port and external input terminal in this machine do not guarantee connection with all types of USB terminal

and AUX terminal. Also, when each terminal does not match the inlet of this machine, a connection is not
available.

• For use of external sound devices and USB memories, follow the manuals for them respectively.

File System Condition

Item

Contents

File system

FAT16/32, no distinction between upper and lower case letters

Number of files

Root folder

Sub folder

FAT16

512

65534

FAT32

65535

65534

Number of layers

16 layers, full pass including file name is within 260 letters

Sort order

Plays in UNICODE order

Supported file format

MP3 / WMA / AAC

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
140
141
142
143
144
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Takeuchi Страницы: 297

Бренд: Fantek Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды