Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 297 / 412

background image

4-65

INSPECTION AND MAINTENANCE

4.17

500 HOUR (6-MONTH) INSPECTION &
MAINTENANCE PROCEDURES

Thoroughly read and understand "SAFETY PRECAUTIONS" of this manual before performing the inspection and
maintenance.
Perform this section together with "EVERYDAY CHECK-UP and 50, 100, 120, and 250 HOUR INSPECTION &
MAINTENANCE PROCEDURES".

4.17.1

REPLACING ENGINE OIL AND ENGINE OIL FILTER

ABOUT HOT PARTS

• Contact with hot parts during operation or immediately after stopping operation may cause burns. Do not touch

the hot parts.

• Immediately after operation, the oil and oil filter are hot. Start the replacement after the temperature goes down.

• Do not reuse the filter element, O-ring and gasket.

• When replacing the O-ring or gasket, check the fitting condition at the mounting surface to prevent it from being

twisted and broken.

• Check drain engine oil, and if metal chips or powder is found in the oil, contact your KOBELCO authorized

dealer/distributor.

• Change the engine oil after 50 hours of operation has been reached for the first time.

• When the engine oil is replaced, replace the engine oil filter as well.

• When the engine oil filter is replaced, run the engine at low idle for several minutes until the oil is filled in the filter.

2

1.

Loosen the five bolts at the under cover just under
the engine and remove the cover.

2.

Place a container for drain oil under drain cock (2).
Container: 17.0 L (4.5 Gal) or more

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
295
296
297
298
299
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: P.Lindberg Страницы: 97

Бренд: JackRabbit Страницы: 22

Бренд: Kubota Страницы: 90

Бренд: Skandia Elevator Страницы: 28

Бренд: Bush Hog Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды