Kobelco SK135SR-7 Скачать руководство пользователя

Страница: 107 / 412

2-33

［

MACHINE FAMILIARIZATION

］

SETTING LIMIT OF AUX FLOW RATE OF ATTACHMENT MODE (ROTARY TILT)

Jog dial operation

Tilting (a,b,c,d) and rotating (e,f) the jog dial

To move the cursor on the monitor and adjust the values
and others.

Pushing down (g) the jog dial

• To switch the screen to the selected setting screen.

•

To determine the adjusted value and others.

AUX

FLOW

CTRL SETTING

AUX FLOW CTRL

SETTING

AUX

FLOW

CTRL SETTING

ANCEL

AUX

FLOW

CTRL SETTING

ANCEL

AUX

FLOW

CTRL SETTING

ANCEL

ETTING OF

DETAILS

UX FLOW

CTRL SETTING

PT 3

PT 2

PT 1

RONT

ATTACHMENT MODE

AUX

FLOW

CTRL SETTING

AUX FLOW CTRL

SETTING

(a)~(f)

(g)

(a )~(f)

(g)

Move the cursor to [AUX FLOW CTRL SETTING] of the icon of the rotary tilt mode.

Push down (g) the jog dial to switch the monitor to the [AUX FLOW CTRL SETTING] screen.

Move the cursor to [ON] of [AUX FLOW CTRL SETTING].

Push down (g) the jog dial to switch the setting to [ON].

Tilt and turn the jog dial to move the cursor to a desired item to set.

Push down (g) the jog dial to enable the selected item to be adjustable.

Item

Adjusting operation pattern

Item possible to be

adjusted *

Independent operation of rotary tilt

(1), (2)*, (3)*

Rotary tilt + arm in combined operation

(1)

Rotary tilt + arm out combined operation

(1)

Rotary tilt + swinging combined operation

(1)

*(2) and (3) can be adjusted only at item A but the adjusted value affects the operability of items B, C, and D.

Tilt and turn the jog dial to a desired value.

Содержание SK135SR-7


































































































































































































































































































































































































Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды

Kobelco SK135SR-7, Руководство по эксплуатации

Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды