Kobelco SK135SR-7 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 412

background image

2-75

［

MACHINE FAMILIARIZATION

2.9.8

FILE PLAYING FUNCTION

Before using this function, pairing (registration of a device) shall be done.

TRACK FORWARD/BACKWARD (USB/BT-AUDIO)

While a USB memory or BT-Audio is being played, press [PRESET 3] or [PRESET 4] to change the track forward/
backward.

If moving track backward is operated after less than 1 sec. from the start of playing the track, the track moves to the
previous track, however, in case of 1 sec. or more from the start, the playing part moves to the beginning of the
same track.
(However, the playing time is not displayed.)

(In case of USB)

• In case of less than 1 sec.

Track number display

Track number display

• In case of 1 sec. or more

Track number display

Playing starts from beginning of same track

Track number display

File number of 1000 or after is displayed as “---“

(In case of BT-Audio)

Due to the Bluetooth device limitation, the track number cannot be displayed.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
147
148
149
150
151
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: achilles Страницы: 94

Бренд: jcb Страницы: 51

Бренд: Savaria Страницы: 28

Бренд: Case Страницы: 22

Бренд: Daewoo Страницы: 16

Бренд: jcb Страницы: 31

Бренд: Hyundai Elevator Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды