Kobelco SK135SR-7 Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 412

background image

2-93

［

MACHINE FAMILIARIZATION

2.10.4

HOW TO USE AIR CONDITIONER

Before turning the air conditioner on, close the doors and windows of the cab to achieve the best performance as
an automatic air conditioner.

COOLING METHOD

To avoid freezing of the evaporator, do not operate the air conditioner for a long time in the COOL-MAX set
temperature with the LO airflow.
If it is frozen and cool air does not flow any longer, turn compressor switch (4) off, set the temperature high, operate
the air conditioner with the maximum airflow "HI", and then turn compressor switch (4) "ON".

8

1

2

3

4

5

6

9

10

7

1.

Operate fan speed selector dial (2) clockwise or
press AUTO control switch (5).

2.

Operate fan speed selector dial (2) clockwise and
set the fan speed HI.

3.

Operate temperature setting dial (1) and set a
desired temperature.

4.

Press compressor switch (4).

5.

Press recirculation air selector switch (6) to select recirculation air.

6.

Operate air outlet mode selector dial (3) and select the VENT outlet (mode 2).

7.

When the temperature inside the cab becomes low, adjust to the temperature and the fan speed to desired
levels.
When AUTO control switch (5) is pressed, the temperature, fan speed, and mode selection become automatic
control.

HEATING METHOD

The engine coolant is used for heating, and it is possible to heat the air when the temperature of the coolant is high.

8

1

2

3

4

5

6

9

10

7

1.

Operate fan speed selector dial (2) clockwise or
press AUTO control switch (5).

2.

Operate fan speed selector dial (2) clockwise and
set the fan speed HI.

3.

Operate temperature setting dial (1) and set a
desired temperature.

4.

Press fresh air selector switch (7) to select fresh air intake.

5.

Operate air outlet mode selector dial (3) and select the foot and front glass outlet (mode 4).

6.

When the temperature inside the cab becomes high, adjust to the temperature and the fan speed to desired
levels.
When AUTO control switch (5) is pressed, the temperature, fan speed, and mode selection become automatic
control.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
165
166
167
168
169
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Yanmar Страницы: 310

Бренд: Wacker Neuson Страницы: 264

Бренд: Meec tools Страницы: 53

Бренд: FlexLink Страницы: 74

Бренд: NPK Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды