Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 145 / 412

background image

2-71

［

MACHINE FAMILIARIZATION

2.9.6

PAIRING (REGISTRATION OF DEVICES)

Bluetooth devices need prior registration of devices to be connected by each other. This registration is called
"pairing".
The pairing is required between this radio component and a mobile phone or other Bluetooth device.
With the OnAir (normal) condition, push the [MODE] key and switch the band to Bluetooth condition.
With the band selecting Bluetooth, press and hold [SOUND/PAIR] to display "WA" and start the preparation of the
pairing.
After the preparation of this radio component is finished, "PA" is displayed, and this radio component enters the
paring waiting condition.
If a device is searched from the Bluetooth device to be connected to this radio component, the screen of that
Bluetooth device displays "BT-****" (* is 4 digits of English letters and numbers). The pairing operation shall be
performed from the Bluetooth device to be connected.
If the paring is performed normally, "P0" is displayed and the pairing is finished normally.
When the pairing is not completed within the limited time (180 sec.) or error occurs, "PX" is displayed and the radio
component returns to the Bluetooth ON condition.
During the pairing operation, by pressing [PWR] key, the pairing is canceled.
* Some mobile phones need entering of a pass key. Enter "0000" as a pass key.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
143
144
145
146
147
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: SANY Страницы: 166

Бренд: JEMA AGRO Страницы: 64

Бренд: jcb Страницы: 24

Бренд: Hitachi Страницы: 340

Бренд: Hitachi Страницы: 28

Бренд: Bestgreen Страницы: 60

IDIG TOUCH XD610

Бренд: Position Partners Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды