Kobelco SK135SR-7 Скачать руководство пользователя

Страница: 174 / 412

2-100

［

MACHINE FAMILIARIZATION

］

2.12.7

FRONT/REAR ADJUSTMENT OF SEAT

(D) The position of the operator's seat can be adjusted back and forth.

Pull up handle (6).

Move the seat back and forth to adjust it to a desired position.

Release the handle to fix the position of the seat.

2.12.8

TILT ADJUSTMENT OF SEAT SEATING SURFACE

(A) The angle of the seating surface of the operator's seat can be adjusted.

Pull up handle (7).

Tilt the seat seating surface to a desired angle to adjust it.

Release the handle to fix the position of the seat seating surface.

2.12.9

FRONT/REAR ADJUSTMENT OF SEAT SEATING SURFACE

(D) The position of the seating surface of the operator's seat can be adjusted back and forth.

Pull up handle (8).

Move the seat seating surface back and forth to adjust it to a desired position.

Release the handle to fix the position of the seat seating surface.

2.12.10 ARM REST ADJUSTMENT

(E) The arm rest can be lifted up, and its angle can be adjusted.

• Arm rest (9) can be lifted up backward.

• Turn control dial (10) at the bottom of arm rest (9) by hand to adjust the angle of the arm rest in the regular

position.

2.12.11 HEAD REST ADJUSTMENT

(F) The head rest can be adjusted by moving it up, down, back, or forth.

• To adjust head rest (11) up or down, hold it with both hands, and move it up or down slightly.

• To adjust head rest (11) back and forth, hold it with both hands, and move it back and forth to a desired position.

2.12.12 SEAT HEATER

Turn seat heater switch (12) "ON" to warm the seat.

This function can be used with the starter switch "ON".

2.12.13 LUMBAR SUPPORT

Adjust the lumber supporting level of the backrest by using adjusting dial (13) of the lumbar support.

Содержание SK135SR-7


































































































































































































































































































































































































Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды

Kobelco SK135SR-7, Руководство по эксплуатации

Результаты поиска

Содержание SK135SR-7

Отзывы:

Похожие инструкции для SK135SR-7

Бренды по названию

Популярные бренды