Keysight E4356A Скачать руководство пользователя

Страница: 68 / 134

Language Dictionary 67

*OPC?

Meaning and Type

Operation Complete

Device Status

Description

This query causes the interface to place an ASCII "1" in the Output Queue when all pending operations are completed.

Pending operations

are as defined for the

*OPC

command. Unlike

*OPC, *OPC?

prevents processing of all subsequent

commands.

*OPC?

is intended to be used at the end of a command line so that the application program can then monitor

the bus for data until it receives the "1" from the power module Output Queue.

Do not follow

*OPC?

with

*TRG

or GPIB bus triggers. Such triggers sent after

*OPC?

will be

prevented from executing and will prevent the power supply from accepting further commands. If this

occurs, the only programmable way to restore operation is by sending the power supply a GPIB

DCL

(Device Clear) command.

Query Syntax

*OPC?

Returned Parameters

<NR1>

ASCII

is placed in the Output Queue when the

power supply has completed operations.

Related Commands

*OPC *TRIG *WAI

*OPT?

Meaning and Type

Option Identification Query

Description

This query requests the power supply to identify any options that are installed. Options are identified by number A.

indicates no options are installed.

Query Syntax

*OPT?

Returned Parameters

<AARD>

*PSC

Meaning and Type

Power-on Status Clear

Device Initialization

Description

This command controls the automatic clearing at power turn-on of:



The Service Request Enable register.



The Standard Event Status Enable register.

If the command parameter =

, then the above registers are cleared at power turn-on. If the command parameter =

, then

the above registers are not cleared at power turn-on but are programmed to their last state prior to power turn on. This is the

most common application for

*PSC

and enables the power module to generate an SRQ (Service Request) at power on.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды