Keysight E4356A Скачать руководство пользователя

Страница: 38 / 134

Front Panel Operation 37

Front Panel Operation

Introduction

This chapter shows you how to operate the front panel. It is assumed that you are familiar with the turn-on checkout

procedure in Chapter 3. That chapter describes how to perform basic power supply functions from the control panel.

operations that you can perform are:



Enabling or disabling the power supply output.



Setting the output voltage and current.



Monitoring the output voltage and current.



Setting the overvoltage protection (OVP) trip point.



Enabling the overcurrent protection (OCP) circuit.



Saving operating states in nonvolatile memory.



Recalling operating states from nonvolatile memory.



Setting the power supply GPIB bus address.



Displaying error codes created during remote operation.



Enabling local (front panel) operation.

Note

You also can calibrate the power supply from the front panel (see Appendix B).

Getting Acquainted

The front panel is summarized in Figure 5-1 and Table 5-1. Note that the panel is organized as follows:



LCD display (including annunciators)



Output VOLTAGE and CURRENT rotary (RPG) knobs



SYSTEM keypad



FUNCTION keypad



ENTRY keypad



Power (LINE) switch

Some keys have two functions. For example, the System

key can be used either to recall a stored operating state or

(store) an operating state. The first operation is shown

the key and the second (shifted) operation is shown in

blue

above

the key. In order to do a shifted operation, first press the solid blue key, which is unlabeled but shown

throughout this manual as

For example, for a recall operation, press the recall key

For a save operation, press the save key, which is

When you do this, the

Shift

annunciator will light to remind you that the

key is now functioning as

the

key. In this chapter, such a shifted operation may be shown simply as

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды