Keysight E4356A Скачать руководство пользователя

Страница: 44 / 134

Front Panel Operation 43

Saving and Recalling Operating States

You can save programming time by storing up to 5 operating states in nonvolatile memory. The front panel programming

parameters that are saved are:



Output voltage, Output current, *OVP voltage,



OCP state (on or off), Output state (enabled or disabled).

Note

More power supply parameters are saved in remote operation. See Chapter 7.

As an example, set up the following state:

Voltage = 45 V Current = 5 A OVP voltage = 48 V.

OCP = on (

OCP

annunciator on) Output = off (

Dis

annunciator on).

Save the above state to location 1 by pressing

. Now set up the following state:

Voltage = 50 V Current = 2.5 A OVP voltage = 55 V.

OCP = off (

OCP

annunciator off) Output = on (

Dis

annunciator off).

Save the above state to location 2 by pressing

Restore the first state by pressing

and verify the parameters. Restore the second state by pressing

. Note how the power supply is automatically programmed each time.

Turn-On Conditions

Whenever you apply power to a new power supply it automatically turns on in a safe reset state with the following

parameters:

off

minimum*

maximum

off

*Minimum is the

*RST

value specified in Table A-2.

It is recommended that you leave the turn-on conditions as programmed. However, you may change them. To do this:

1. Set up the power supply to the state you want when it is turned on.

2. Store that state to location 0.

3. Turn off the power supply.

4. Hold in the

key and turn the power supply back on. The display indicates

RCL 0 PWR-ON

to verify that the power

supply has configured its turn-on state to that stored in location 0.

5. From now on the unit will always turn on to the state defined in location 0.

To return the power supply to the original factory reset state, hold down the

key when you turn on the unit. The display

indicates

RST POWER-ON

to verify that the power supply has configured its turn-on state to the original reset state. From

now on it will continue to turn on in that state.

Setting The GPIB Address

Types of Power supply GPIB Addresses

Figure 4-8 in Chapter 4 shows the ways the power supply can be connected to the GPIB bus. You can set up the GPIB

address in one of three ways:

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды