Keysight E4356A Скачать руководство пользователя

Страница: 74 / 134

Language Dictionary 73

Current Subsystem

This subsystem programs the output current of the power supply.

CURR
CURR:TRIG

These commands set the immediate current level or the pending triggered current level of the power supply. The immediate

level is the current programmed for the output terminals. The pending triggered level is a stored current value that is

transferred to the output terminals when a trigger occurs. A pending triggered level is unaffected by subsequent

CURR

commands and remains in effect until the trigger subsystem receives a trigger or an

ABORt

command is given. If there is

no pending

CURR:TRIG

level, then the query form returns the

CURR

level. In order for

CURR:TRIG

to be executed,

the trigger subsystem must be initiated (see

INITiate).

Command Syntax

[SOURce]:CURRent[:LEVel] [:IMMediate][:AMPLitude] <NRf+>

[SOURce][:CURRent[:LEVel]:TRIGgered [:AMPLitude] <NRf+>

Parameters

Table 7-1

Default Suffix

*RST Value

Table 7-1

Examples

CURR 200

CURRENT:LEVEL 200 MA

CURRENT:LEVEL:IMMEDIATE:AMPLITUDE 2.5

CURR:TRIG 20

CURRENT:LEVEL:TRIGGERED 20

Query Syntax

[SOURce]:CURRent[:LEVel] [:IMMediate][:AMPLitude]?

[SOURce]:CURRent[:LEVel] [:IMMediate][:AMPLitude]? MAX

[SOURce]:CURRent[:LEVel] [:IMMediate][:AMPLitude]? MIN

[SOURce]:CURRent[LEVel]:TRIGgered [:AMPLitude]?

[SOURce]:CURRent[LEVel]:TRIGgered [:AMPLitude]? MAX

[SOURce]:CURRent[:LEVel]:TRIGgered [:AMPLitude]? MIN

Returned Parameters

<NR3> CURR?

and

CURR:TRIG?

return presently programmed immediate and

triggered levels. If not triggered level is programmed, both returned values are the same.

CURR? MAX

and

CURR? MIN

return the maximum and minimum programmable

immediate current levels.

CURR:TRIG? MAX

and

CURR:TRIG? MIN

return the maximum and minimum

programmable triggered current levels.

Related Commands

For

CURR

*SAV *RCL

*RST

For

CURR:TRIG

ABOR CURR *RST

CURR:PROT:STAT

This command enables or disables the power supply overcurrent protection (OCP) function. If the overcurrent protection

function is enabled and the power supply goes into constant-current operation, then the output is disabled and the

Questionable Condition status register OC bit is set (see "Chapter 8 - Status Reporting"). An overcurrent condition can be

cleared with the

OUTP:PROT:CLE

command after the cause of the condition is removed.

Command Syntax

[SOURce]:CURRent:PROTection:STATe <bool>

Parameters

0 | 1 | OFF | ON

*RST

Value

OFF

Examples

CURR:PROT:STAT 0 CURRENT:PROTECTION:STATE OFF

CURR:PROT:STAT 1 CURRENT:PROTECTION:STATE ON

Query Syntax

[SOURce]:CURRent:PROTection:STATe?

Returned Parameters

<NRI>

Related Commands

OUTP:PROT:CLE *RST

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды