Keysight E4356A Скачать руководство пользователя

Страница: 83 / 134

82 Language Dictionary

System Commands

System commands query error messages and software versions, and program system language functions.

SYST:ERR?

This query returns the next error number followed by its corresponding error message string from the remote programming

error queue. The queue is a FIFO (first-in, first-out) buffer that stores errors as they occur. As it is read, each error is

removed from the queue. When all errors have been read, the query returns

NO ERROR

. If more errors are accumulated

than the queue can hold, the last error in the queue will be

-350,TOO MANY ERRORS

(see Appendix D for other error codes).

You can use the power supply front panel

key to read errors from the queue. Errors generated at the front panel are

not put into the queue but appear immediately on the display.

Query Syntax

SYSTem:ERRor?

Parameters

(None)

Returned Parameters

<NRI>,<SRD>

Examples

SYST:ERR?

SYSTEM:ERROR?

Related

Commands

(None)

SYST:LANG

This command switches the interface between its SCPI (TMSL) command language and its compatibility language. The

compatability language is provided for emulation of older power supply systems and is described in Appendix G. Sending

the command causes:



The alternate language to become active and to be stored in nonvolatile memory.



The power supply to reset to the state stored in Location 0.

If the power supply is shut off, it will resume operation in the last-selected language when power is restored.

Command Syntax

SYSTem:LANGuage <string>

Syntax is the same, regardless of the present language.

Parameters

TMSL | COMPatibility

Note:

Parameter TMSL must be used in place of

SCPI.

Default Value

TMSL or last

selected language.

Examples

SYST:LANG TMSL SYSTEM:LANGUAGE COMPATIBILITY

Query Syntax

SYSTem:LANGuage?

Returned Parameters

<CRD>

TMSL | COMP

Related Commands

(None)

SYST:VERS?

This query returns the SCPI version number to which the power supply complies. The returned value is of the form

YYYY.V, where

YYYY

represents the year and

is the revision number for that year.

Query Syntax

SYSTem:VERSion?

Parameters

(none)

Returned Parameters

<NR2>

Examples

SYST:VERS? SYSTEM:VERSION?

Related Commands

(None)

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды