Keysight E4356A Скачать руководство пользователя

Страница: 14 / 134

General Information 13

General Information

Introduction

The following Getting Started Map will help you find the information you need to complete the specific task that you want

to accomplish. Refer to the table of contents or index of each guide for a complete list of the information contained within.

Table 1-1. Getting Started Map

Task

Where to find information

General information

Capabilities and characteristics

Chapter 1

Installing the unit

Location

Line connections

Chapter 2

Checking out the unit

Verifying proper operation

Using the front panel

Chapter 3

Making Connections

Load connections

Computer connections

Application Information

Chapter 4

Using the front panel

Front panel keys

Front panel examples

Chapter 5

Using the programming interface

GPIB interface

Chapter 6

Programming the unit using SCPI (and COMPatibility) commands

SCPI commands

SCPI programming examples

SCPI language dictionary

Chapters 7 and 8 for SCPI commands.

Appendix G for COMPatibility commands

Installing the Keysight VXI

plug&play

instrument driver

NOTE:

The driver must be installed on your pc to access the on-line

information. Drivers are available on the web at

www.keysight.com/go/drivers

Chapter 2

Safety Considerations

This power supply is a Safety Class 1 instrument, which means it has a protective earth terminal. That terminal must be

connected to earth ground through a power source equipped with a 3-wire ground receptacle. Refer to the Safety Summary

page at the beginning of this guide for general safety information. Before installation or operation, check the power supply

and review this guide for safety warnings and instructions. Safety warnings for specific procedures are located at

appropriate places in the guide.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды