Keysight E4356A Скачать руководство пользователя

Страница: 54 / 134

Remote Programming 53

Programming Voltage and Current

The following statements program both voltage and current and return the actual output from the sense terminals:

OUTP OFF

Disable the output.

VOLT 45;CURR 25

Program the voltage and current.

VOLT?;CURR?

Read back the programmed levels.

OUTP ON

Enable the output.

MEAS:VOLT?;MEAS:CURR?

Read back the outputs from the sense terminals.

Programming Protection Circuits

This example programs the voltage and current, programs an overvoltage protection value, and turns on the overcurrent

protection. It then reads back all the programmed values.

VOLT:LEV 45;PROT 47.5

Program the voltage and overvoltage protection.

CURR:LEV 25;PROT:STAT ON

Program the current and overcurrent protection.

VOLT:LEV?;PROT?;:CURR:LEV?;PROT:STAT?

Read back the programmed values.

Note the required use of the optional

LEVel

header in the above example (see "The Effect of Optional Headers", given

previously).

Changing Outputs by Trigger

If you do not program pending triggered levels, they default to the programmed (immediate) output levels. The following

statements shows some basic trigger commands.

OUTP OFF

Disable the output.

VOLT:LEV:IMM 22;TRIG 25

Program the (immediate) voltage level to 22V and the pending
triggered level to 25 V.

CURR:LEV:IMM I5;TRIG 25

Program the (immediate) current level to 15 A and the pending
triggered level to 25 A.

VOLT:LEV:IMM?;TRIG?;:CURR:LEV:IMM?;TRIG?

Check all the programmed values.

OUTP ON

Enable the output.

MEAS:VOLT?;CURR?

Read back the immediate levels from the sense terminals.

INIT;TRIG

Arm the trigger circuit and send a single trigger.

INIT;*TRG

Same as above, except using a common command.

MEAS:VOLT?;CURR?

Read back the triggered levels from the sense terminals.

If you need to send two or more triggers, program the trigger circuit for continuous arming.

OUTP OFF

Disable the output.

VOLT:LEV:IMM 5O;TRIG 25

Program the (immediate) voltage level to 50 V and the pending
triggered level to 25 V.

INTIT:CONT ON

Program the trigger circuit for continuous arming.

OUTP ON

Enable the output to 50 V.

TRIG

Trigger the output voltage to 25 V.

VOLT:TRIG 50;:TRIG

Set the pending trigger level to 50 V and trigger the output
voltage back to 50 V.

INTIT:CONT OFF

Remove the continuous triggger arming.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды