Keysight E4356A Скачать руководство пользователя | Manualshive

Страница: 4 / 134

background image

3

Safety Summary

The  following  general  safety  precautions  must  be  observed  during  all  phases  of  operation,  service,  and  repair  of  this
instrument.  Failure  to  comply  with  these  precautions  or  with  specific  warnings  elsewhere  in  this  manual  violates  safety
standards  of  design,  manufacture,  and  intended  use  of  the  instrument.  Keysight  Technologies  Company  assumes  no
liability for the customer's failure to comply with these requirements.

GENERAL.

This product is a Safety Class 1 instrument (provided with a protective earth terminal).

Any LEDs used in this product are Class 1 LEDs as per IEC 825-l.

This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada.

ENVIRONMENTAL CONDITIONS

With the exceptions noted, all instruments are intended for indoor use in an installation category II, pollution degree 2 environment.

They are designed to operate at a maximum relative humidity of 95% and at altitudes of up to 2000 meters. Refer to the specifications

tables for the ac mains voltage requirements and ambient operating temperature range.

BEFORE APPLYING POWER.

Verify that the product is set to match the available line voltage and the correct fuse is installed.

GROUND THE INSTRUMENT.

To minimize shock hazard, the instrument chassis and cabinet must be connected to an electrical ground. The instrument must be

connected to the ac power supply mains through a three-conductor power cable, with the third wire firmly connected to an electrical

ground (safety ground) at the power outlet. For instruments designed to be hard-wired to the ac power lines (supply mains), connect the

protective earth terminal to a protective conductor before any other connection is made. Any interruption of the protective (grounding)

conductor or disconnection of the protective earth terminal will cause a potential shock hazard that could result in personal injury. If the

instrument is to be energized via an external autotransformer for voltage reduction, be certain that the autotransformer common terminal

is connected to the neutral (earthed pole) of the ac power lines (supply mains).

FUSES.

Only fuses with the required rated current, voltage, and specified type (normal blow, time delay, etc.) should be used. Do not use repaired

fuses or short circuited fuseholders. To do so could cause a shock or fire hazard.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE.

Do not operate the instrument in the presence of flammable gases or fumes.

KEEP AWAY FROM LIVE CIRCUITS.

Operating personnel must not remove instrument covers. Component replacement and internal adjustments must be made by qualified

service personnel. Do not replace components with power cable connected. Under certain conditions, dangerous voltages may exist even

with the power cable removed. To avoid injuries, always disconnect power, discharge circuits and remove external voltage sources before

touching components.

DO NOT SERVICE OR ADJUST ALONE.

Do not attempt internal service or adjustment unless another person, capable of rendering first aid and resuscitation, is present.

DO NOT EXCEED INPUT RATINGS.

This instrument may be equipped with a line filter to reduce electromagnetic interference and must be connected to a properly grounded

receptacle to minimize electric shock hazard. Operation at line voltages or frequencies in excess of those stated on the data plate may

cause leakage currents in excess of 5.0 mA peak.

DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT.

Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modification to the

instrument. Return the instrument to a Keysight Technologies Sales and Service Office for service and repair to ensure that safety

features are maintained.

Instruments which appear damaged or defective should be made inoperative and secured against unintended operation until they can be

repaired by qualified service personnel.

«
...
2
3
4
5
6
...
»

Содержание E4356A







































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4356A

Бренд: YIHUA Страницы: 2

Бренд: Valex Страницы: 8

Бренд: Icom Страницы: 2

Бренд: Velleman Страницы: 9

Бренд: Nakayama Страницы: 101

Бренд: Pulsar Страницы: 40

Бренд: Parkside Страницы: 138

Бренд: Harrington Страницы: 2

Бренд: Parkside Страницы: 202

Бренд: H3C Страницы: 15

Craftsman 113.213850

Бренд: Sears Страницы: 24

Бренд: FXA Страницы: 56

Бренд: P.I.T. Страницы: 24

Бренд: R&S Страницы: 176

Бренд: Shop fox Страницы: 64

Бренд: H3C Страницы: 6

Бренд: Max Страницы: 58

Бренд: Panduit Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды