Keysight E4356A Скачать руководство пользователя

Страница: 117 / 134

116 Digital Port Functions

Digital I/O Operation

The digital port can be configured (see Figure F-4) to provide a digital input/output to be used with custom digital interface

circuits or relay circuits. Some examples are shown Figure F-5. See Figure F-1 for the pin assignments of the mating plug

and Appendix A for the electrical characteristics of the port. See

DIG:DATA[:VAL]

in “Chapter 7 - Language Dictionary"

for information on programming the port. The digital port pins are as follows:

OUT 0

(pin 1)

This port can only be used as an open-collector output. It is assigned a bit weight of 1.

OUT 1

(pin 2)

This port can only be used as an open-collector output. It is assigned a bit weight of 2.

IN/OUT 2

(pin 3)

This port can be programmed to be either an input, or an open-collector output with an internal

4.6 k pull-up to 5 V.

Common

(pin 4)

This pin is the common connection for the Digital I/O ports.

+ - +

INH FLT

. . . .

NOTE: Connectors
are removable

4 3 2 1

Coil Current
0.25 A Max.

+16.5 V Max.

Relay Driver

Ports 0,1,2

Supply contains
internal clamp diodes
for inductive flyback.

A) Relay Circuits

4 3 2 1

B) Digital Interface Circuits

Digital Output

Ports 0,1, 2

Digital Intput

Port 2

TTL, AS,
CMOS, HC

External pull-up to 5 V
required for pins 1 & 2.

Figure F-5. Digital l/O Port Applications

Relay Link Operation

The digital port can be configured to provide relay control outputs for the Keysight 59510A or 59511A Relay Accessory.

Refer to Figure F-1 for the pin assignments of the mating plug.

Not used with units that output more than 50 amps.

RLY SEND

(pin 1)

(pin 2 is not used)

Provides the serial data to control the relays in the Relay Accessory.

RLY RTN

(pin 3)

Receives the data readback that indicates the status of the relays in the Relay Accessory.

Common

(pin 4)

Common connection for the RLY SEND and RLY RTN lines.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды