Keysight E4356A Скачать руководство пользователя

Страница: 81 / 134

80 Language Dictionary

STAT:OPER:NTR
STAT:OPER:PTR

These commands set or read the value of the Operation NTR (Negative-Transition) and PTR (Positive-Transition) registers.

These registers serve as polarity filters between the Operation Enable and Operation Event registers to cause the following

actions:



When a bit in the Operation NTR register is set to 1, then a 1-to-0 transition of the corresponding bit in the

Operation Condition register causes that bit in the Operation Event register to be set.



When a bit of the Operation PTR register is set to 1, then a 0-to-1 transition of the corresponding bit in the

Operation Condition register causes that bit in the Operation Event register to be set.



If the same bits in both NTR and PTR registers are set to 1, then

any transition

of that bit at the Operation

Condition register sets the corresponding bit in the Operation Event register.



If the same bits in both NTR and PTR registers are set to 0, then

no transition

of that bit at the Operation

Condition register can set the corresponding bit in the Operation Event register.

Note

Setting a bit in the value of the PTR or NTR filter can of itself generate positive or negative events in the

corresponding Operation Event register.

Command Syntax

STATus:OPERtion:NTRansition <NRf>

STATus:OPERtion:PTRansition <NRf>

Parameters

32727

Suffix

(None)

Default Value

Examples

STAT:OPER:NTR 32 STAT:OPER:PTR 1312

Query Syntax

STAT:OPER:NTR? STAT:OPER:PTR?

Returned Parameters

<NR1>

(Register value)

Related Commands

STAT:OPER:ENAB

Status Questionable Registers

Bit Configuration of Questionable Registers

Bit Position

15-11

Condition

UNR RI

Bit Weight

1024 512

256

128

NU = (Not used); OC = Overcurrent protection circuit has tripped.

OT = Overtemperature status condition exists; OV = Overvoltage protection circuit has tripped.

RI = Remote inhibit is active; UNR = Power supply output is unregulated.

Note:

See "Chapter 4 - Status Reporting" for more explanation of these registers.

STAT:OUES?

This query returns the value of the Questionable Event register. The Event register is a read-only register which holds

(latches) all events that are passed by the Questionable NTR and/or PTR filter. Reading the Questionable Event register

clears it.

Query Syntax

STATus:QUEStionable[:EVENt]?

Parameters

(None)

Returned Parameters

<NR1>

(Register Value)

Examples

STAT:QUES?

STATUS:QUESTIONABLE:EVENT?

Related Commands

*CLS STAT:QUES:ENAB STAT:QUES:NTR

STAT:QUES:PTR

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды