Keysight E4356A Скачать руководство пользователя

Страница: 120 / 134

Compatibility Language 119

Compatibility Language

Introduction

This power supply is programatically compatible with the Keysight 603xA Series AutoRanging Power Supplies (ARPS).

This means that you can program this power supply over the GPIB using the ARPS commands. Software that you have

written for the autoranging power supplies can also be adapted to program this power supply.

Note

The Keysight E4356A Power supply's serial link is not supported by ARPS commands. You can use only

a GPIB primary address for the power supply.

To switch from SCPI commands to ARPS commands (and vice versa), use the SYST:LANG command. This command is

documented in Chapter 7.

Table G-1 summarizes the ARPS commands that program the supplies. You will need to refer to the Series 603xA power

supply manual (see Table 1-4) for complete information on the ARPS commands. Some of the ARPS commands are

similax to SCPI commands, but others are unique to ARPS. For example, the ARPS FOLD commands have no function

with the Keysight E4356A power supplies. Similarly, there are some SCPI commands that have no ARPS function.

Parallel Polling

When programmed for parallel polling and Compatibilty Language, power supplies operating under the Keysight BASIC

system can "hang up" the GPIB when the system is turned on. This can occur under the following conditions:



The controller uses CS80 Protocol for an external disk drive (for example, the Keysight 9133D).



The external disk drive and the power supply have the same select code and that code is 7 or less.



The external disk drive and power supply addresses are binary complements of each other (e.g., 0 & 7, 1 & 6, etc.)

When the system is turned on, the power supply accesses the GPIB before the controller and prevents it from accessing the

external disk drive. The solution is to change one of the GPIB addresses, or to ensure that the power supply is not turned on

until after the controller has completed its selftest and has control of the GPIB.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды