Keysight E4356A Скачать руководство пользователя

Страница: 114 / 134

Digital Port Functions 113

Digital Port Functions

Digital Connector

A 4-pin connector and a quick-disconnect mating plug are provided for digital input and output signals (see Figure F-l for

wiring connections, and Table A-2 for electrical characteristics). This digital port can be configured to provide either

Fault/Inhibit or Digital I/O functions.

Note

Consistent with good engineering practice, twist and shield all signal wires to and from the digital

connector.

Figure F-1. Digital Port Connector

Fault/Inhibit Operation

As shipped from the factory, the digital port is configured to provide a fault indicator (FLT) output and a remote (INH)

input. Unplug the mating plug to make the connections. After you have finished making all connections, plug the wired plug

back into the connector.

FLT Output

(pins 1 and 2)

Used to indicate that a fault has occurred in power supply. Pins 1 and 2 are the open collector

output of an optocoupler, with pin 1 the collector and pin 2 the emitter. When a fault has

occurred, pin 1 is driven low with respect to pin 2 (negative-true).

INH Input

(pin 3)

Used to shut down the power supply output. Pin 3 is a high impedance input. The unit shuts

down when this input is driven low (negative-true). This can be done by shorting pin 3 to pin 4.

INH Common

(pin 4)

Provides the common connection for the INH input.

Three examples are provided to show how to use the FLT/INH circuits of your power supply. Use twisted wire connections

to reduce or prevent EM in all cases. If shielded wire is used, connect only one end of the shield to the chassis signal ground

binding post to prevent ground loops.

In Figure F-2, the INH input is connected to a switch that shorts pin 3 to pin 4 whenever it is necessary to externally disable

the output of the unit. This will activate the remote inhibit (RI) fault protection circuit, causing the front panel

Prot

annunciator to come on. It also sets the RI event bit in the unit's Questionable Status Event register (see "Chapter 8 - Status

Reporting" ). To re-enable the unit after it has been disabled by the INH input, first open the connection between pins 3 and

4. Then clear the protection circuit either from the front panel (see "Chapter 5 - Front Panel Operation" in this guide) or

over the GPIB (see the Programming Guide).

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды