Keysight E4356A Скачать руководство пользователя

Страница: 34 / 134

User Connections 33



Analog Connector



Slave Unit



Master Unit



Program only the master. Set slave output and OVP slightly higher than the master to ensure that slave stays in CC mode



Load



Load Connection

Only local sensing permitted

Connect for optional remote sensing

Figure 4-7. Auto-Parallel Connection (Remote Sensing Optional)

Auto-Parallel Programming.

Program only the first ("master") unit in the series; the "slave" units automatically track the

master's output. However, the voltage and OVP settings of the slave units must be set higher than the operating voltage of

the master unit. This ensures that the slave units will operate in CC mode. Functions such as status, voltage readback, and

current readback can still be read back individually for each unit.

If a "slave" unit experiences a desired shutdown condition (such as overtemperature or overcurrent), it will not

automatically shut down all other units. You must first enable remote inhibit (RI) and discrete fault indicator (DFI)

operation. See "Fault/Inhibit Operation" in Appendix F for wiring information and "Questionable Status Group" in Chapter

8 for programming information.

Connecting Units in Series

Floating voltages must not exceed 240 Vdc. No output terminal may be more than 240 V from chassis

ground.

Figure 4-8 shows how power supplies can be connected in series for higher voltage output. Series connections are

straightforward in this case.

Program each power supply independently. If two units are used in the series configuration, program each unit for 50% of

the total output voltage. Set the current limit of each unit to the maximum that the load can handle without damage.

Each power supply has a reverse voltage protection diode across its output. If a reverse voltage is

applied, the unit cannot control the current conducted through this diode. To avoid damaging the

unit, never connect it in such a way that a reverse voltage can force it to conduct current in excess

of the unit's maximum reverse diode current (see Table A-2).

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды