Keysight E4356A Скачать руководство пользователя

Страница: 84 / 134

Language Dictionary 83

Trigger Subsystem

This subsystem controls remote triggering of the power supply.

TRIG

When the trigger subsystem is enabled,

TRIG

generates a trigger signal. The trigger will then:

1. Initiate a pending level change as specified by

CURR[:LEV]:TRIG

VOLT[:LEV]:TRIG.

2. Clear the WTG bit in the Status Operation Condition register.

3. If

INIT:CONT

has been given, the trigger subsystem is immediately re-enabled for subsequent triggers. As soon as it

is cleared, the WTG bit is again set to 1.

Command Syntax

TRIGger[:IMMediate]

Parameters

(None)

Examples

TRIG TRIGGER:IMMEDIATE

Query Syntax

(None)

Related Commands

ABOR CURR:TRIG INIT *TRG VOLT:TRIG

TRIG:SOUR

This command selects the trigger source. Since the power supply has no other trigger source than the GPIB bus, this

command need not be used. It is included in the command set to provide programming compatibility with other instruments

(such as the Keysight Electronic Load family) that may have more than one trigger source.

Command Syntax

TRIGer:SOURce <CRD>

Parameters

BUS

*RST Value

BUS

Examples

TRIG:SOUR BUS TRIGGER:SOURCE BUS

Query Syntax

TRIGger:SOURce?

Returned Parameters

BUS

Related Commands

*RST *TRG TRIG[:IMM]

Voltage Subsystem

This subsystem programs the output voltage of the power supply.

VOLT
VOLT:TRIG

These commands set the immediate voltage level or the pending triggered voltage level of the power supply. The immediate

level is the voltage programmed for the output terminals. The pending triggered level is a stored voltage value that is

transferred to the output terminals when a trigger occurs. A pending triggered level is unaffected by subsequent

VOLT

commands and remains in effect until the trigger subsystem receives a

trigger or an

ABORt

command is given. If there is

no pending

VOLT:TRIG

level, then the query form returns the

VOLT

level. In order for

VOLT:TRIG

to be executed,

the trigger subsystem must be initiated (see

INITiate).

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды