Keysight E4356A Скачать руководство пользователя

Страница: 36 / 134

User Connections 35

Programming.

Note from Figure 4-1 that you have three options for programming the current. You can use a voltage

source that is positive, negative, or floating with respect to

Common

P. Do not exceed



15 V with respect to

Common

Make certain that the common connection for your voltage programming source is isolated from the

load. Failure to do this may cause damage to the power supply.

The effect of the analog programming source is always summed with the values programmed over the GPIB or from the

front panel. The voltage source can act alone only if you set the other program sources to zero. Keep the total programmed

setting of the unit (the analog input summed with the GPIB or front panel settings) at or under the output ratings specified in

Table A-2. Exceeding the output ratings will not damage the unit, but it may not be able to regulate its output at the higher

levels. If this happens, the

Unr

annunciator will light to warn you that the output is unregulated.

Controller Connections

Figure 4-10 shows two basic ways of connecting your power supply to a controller. They are "linked" and "stand-alone

configurations.

Stand-Alone Connections

See Figure 4-10A. Each stand-alone power supply has its own GPIB bus address. Stand-alone power supplies may

be connected to the bus in series configuration, star configuration, or a combination of the two. You may connect

from 1 to 15 stand-alone power supplies to a controller GPIB interface.

Linked Connections

See Figure 4-10B. Up to 16 power supplies may be used at a single GPIB primary bus address by making linked

connections. (You cannot use linked connections if you intend to program power supplies with the Compatibility

Language - see the Appendix G.)



The first power supply in a linked connection is a "direct unit" connected to the controller via a GPIB cable. The

direct unit is the only unit connected directly to the bus and has a unique primary bus address.



The remaining power supplies are "linked units” connected to the direct unit via a serial-link cable. Each linked unit

has a unique secondary GPIB address and derives its primary address from the direct unit. You may connect from 1

to 15 linked supplies to each direct unit.

Note

The power supply is shipped from the factory with its GPIB address set to 5. The power supply primary

and secondary addresses can be changed from the front panel as described in Chapter 6 - "Remote

Programming". For power supply GPIB interface capabilities, see Table 1-5 in Chapter 1 of this guide.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды