Keysight E4356A Скачать руководство пользователя

Страница: 79 / 134

78 Language Dictionary

OUTP:REL

This command is valid only if the power supply is configured for the optional relay connector. Programming

closes the

relay contacts; programming

OFF

opens them. The relay is controlled independently of the output state. If the power

supply is supplying power to a load, that power will appear at the relay contacts during switching. If the power supply is not

configured for the relay option, sending either relay command generates an error.

Command Syntax

OUTPut:RELay[:STATe] <bool>

Parameters

0 | 1 | OFF | ON

*RST Value

Examples

OUTP:REL 1 OUTP:REL OFF

Query Syntax

OUTPput:RELay?

Returned Parameters

0 |1

Related Commands

OUTP[:STAT] *RCL *SAV

OUTP:REL:POL

This command is valid only if the power supply is configured for the optional relay connector. Programming

NORMal

causes the relay output polarity to be the same as the power supply output. Programming

REV

erse causes the relay output

polarity to be opposite to that of the power supply output. If

OUTP[:STAT] = ON

when either relay command is sent, the

power supply output voltage is set to 0 during the time that the relays are changing polarity. If the power supply is not

configured for the relay option, sending either relay command generates an error.

Command Syntax

OUTPut:RELay:POLarity <CRD>

Parameters

NORMal | REVerse

*RST Value

NORM

Examples

OUTP:REL:POL NORM

Query Syntax

OUTPput:RELay:POLarity?

Returned Parameters

NORM | REV

Related Commands

OUTP[:STAT] *RCL *SAV

Status Subsystem

This subsystem programs the power supply status registers. The power supply has three groups of status registers;

Operation, Questionable,

and

Standard Event.

The Standard Event group is programmed with Common commands as

described in "Chapter 8 - Status Reporting". The Operation and Questionable status groups each consist of the Condition,

Enable, and Event registers and the NTR and PTR filters.

STAT:PRES

This command sets all defined bits in the Status Subsystem PTR registers and clears all bits in the subsystem NTR and

Enable registers. STAT:OPER:PTR is set to 1313 and STAT:QUES:PTR is set to 1555.

Command Syntax

STATus:PRESet

Parameters

(None)

Examples

STAT:PRES STATUS:PRESET

Query Syntax

(None)

Related Commands

(None)

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды