Keysight E4356A Скачать руководство пользователя

Страница: 40 / 134

Front Panel Operation 39

Table 5-1. Front Panel Controls and Indicators (continued)



SYSTEM Keys

When the power supply is under remote control, press to enable local operation.

This control can be

defeated by a lock-out command over the GPIB

Press to display the power supply's GPIB address. You can change the address with the

ENTRY

keys

Use to display error codes generated during remote operation. (Select by pressing

Use to restore a previously saved power supply state. Use ENTRY keys

through

to specify which

location to recall. (Select by pressing

Note:

Location 0 may contain the power supply turn-on state. See "Turn-on operation" in this chapter.

Use to save the power supply’s present state to nonvolatile memory. (Select by pressing

.) Use

ENTRY keys to specify the location where you want to store the state. Use locations

through

This unlabeled blue key is the Shift key. Press to access the shifted (alternate) key functions.



Function Keys

Press to enable or disable the power supply output. This key toggles between the two states. The disabled

state programs the output to the

*RST

voltage and current settings.

Press to display the output voltage setting. After pressing

, you may use the ENTRY keys to change

the value.

Press to display the output current setting. After pressing

you may use the ENTRY keys to change

the value.

Press to display the OV trip voltage setting. After pressing

, you may use the ENTRY keys to change

the value.

When the

Prot

annunciator is on, press

to see which protection circuit caused the power supply to

shut down. Response can be OC (overcurrent), OT (overtemperature), or OV (overvoltage). If no protection

circuit has tripped, the display will show dashes (- - - -).

Press this key to reset the protection circuit.

If the condition that caused the circuit to trip has been

removed,

the

Prot

annunciator will go off.

Press to enable or disable the power supply OCP trip circuit. This key toggles between the two states. which

are indicated by the

OCP

annunciator.



ENTRY Keys

Press to increment the output voltage in the CV mode, or to increase the voltage setting after you have

pressed the

key.

Press to decrement the output voltage in the CV mode, or to decrease the voltage setting after you have

pressed the

key.

Press to increment the output current in the CC mode, or to increase the current setting after you have

pressed the

key.

Press to decrement the output current in the CC mode, or to decrease the current setting after you have

pressed the

key.

Press to select numerical values.

Press to enter a minus sign.

Press to delete the last keypad entry. Use this key to remove one or more incorrect digits before they are

entered.

These four entry keys operate in two modes. Press and release for a single minimal change as determined

by the programming resolution (see Table A-2). Press and hold for an increasingly rapid output change.

Press to delete an entire keypad entry and return to the meter mode. Use this key to exit from a value before

it is entered.

Press to enter a value or to accept an existing value and return the display to the meter mode.

The remaining shifted keys are for calibration (see Appendix B - "Calibration").

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды